BİTÜMLÜ
SU YALITIM ÖRTÜSÜ
APP or SBS modified, minerals, aluminium foil or PE film covered, with fiberglass or polyester mat reinforced waterproofing membranes at various thicknesses.
Description :
BITUMINOUS WATERPROOFING MEMBRANE are composed of APP or SBS modified bitumen, upper surface is coated by PEfilm, minerals or aluminium foil on two types of reinforcements which are fiberglass and non woven polyester mat.
Uses :
- Terrace roofs of buildings, curtain walls, foundations.
- Sloping concrete roofs,
- On light metallic and prefabricated roofs.
- It is only used in a single layer for insulation purposes against moisture in such wet spaces as bathrooms and kitchens and in foundations where there is no pressurized ground and surface water. Other than this, it is not used in a single layer.
- Please consult us for other application substrates.
Advantages:
- It is flexible , moves with the building
- it will last as long as the building lasts.
- It has very high adherence
- It can be applied to the concrete wooden and metal surfaces
Product Data :
| Composition | : | APP or SBS modified bitumen |
| Application Method | : | By Torch |
| Surface | : | Bottom Surface : PE Film
Top Surface : PE Film, Colored Minerals,or Alumunium Foil |
| Flow resistance at elevated temperature | : | +110°C (for APP modifying)
+100°C (for SBS modifying) |
| Length | : | 10 meters ( for 3mm thickness)
15 meters ( for 2mm thickness) |
| Width | : | 1 meter |
| Flexibility at low temperature | : | -5 -10°C (for APP modifying)
-20°C (for SBS modifying) |
| Tensile Strength | : | Varies due to composition and reinforcement type |
Surface Preparation :
The surface should be cleaned of any grease, dust, rust before any application..
Application :
FİLİM1KAT is advised to use as primer before Nafta Osmanli Waterproofing Membrane application. The consumption of primer strictly depends on porosity of the substrate and be approximately 0.2-0.3 l/m².
After primer application, membranes are heated by using torch and adhered to the surface immediately. Membranes should be overlapped 10 cm on the short sides and 15 cm on the ending points. If second layer is required, application should be done due to center alignment approach( 50 cm from the short side, and 5meters from the long side).
Storage :
Store vertically in a cool and dry conditions (+5°C to +35°C). Protect rolls from the direct sun.
Package :
Rolls of 1m wide and 10meters (3mm thickness), or 15 meters (2mm thickness) long.
| Essential Characteristics | Performance | ||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Unit | Tolerance | PC 200 | PC 300 | PP 200 | PP 300 | PP 400 | PC 40M | PP 40M | OPC 2000 | OPC 3000 | OPP 3000 | OPP 4000 | OPP 400M | OPA 3000 | OPP 40VG | OSC 2000 | OSC 3000 | OSP 3000 | OSP 4000 | OSP 40M | |
| Visible Defects | - | - | PASS | ||||||||||||||||||
| Lenght | m | ± 0.05 | 15 | 10 | 15 | 10 | 10 | 10 | 10 | 15 | 10 | 10 | 10 | 10 | 10 | 10 | 15 | 10 | 10 | 10 | 10 |
| Width | m | ± 0.02 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 |
| Thickness | mm | ± 0.2 | 2 | 3 | 2 | 3 | 4 | 3.5 | 3.5 | 2 | 3 | 3 | 4 | 3.5 | 3 | 4 | 2 | 3 | 3 | 4 | 3.5 |
| Straightness | - | - | PASS | ||||||||||||||||||
| Tensile Strenght (long) | N/50mm | ±%30 | 300 | 300 | 600 | 600 | 800 | 400 | 800 | 400 | 400 | 800 | 800 | 800 | 800 | 1000 | 400 | 400 | 800 | 800 | 800 |
| Tensile Strenght (trans) | N/50mm | ±%30 | 200 | 200 | 400 | 400 | 600 | 300 | 600 | 300 | 300 | 600 | 600 | 600 | 600 | 800 | 300 | 300 | 600 | 600 | 600 |
| Elongation (Length) | % | ± 10 | 2 | 2 | 30 | 30 | 35 | 2 | 35 | 2 | 2 | 35 | 35 | 35 | 35 | 40 | 2 | 2 | 35 | 35 | 35 |
| Elongation (Trans) | % | ± 10 | 2 | 2 | 30 | 30 | 35 | 2 | 35 | 2 | 2 | 35 | 35 | 35 | 35 | 40 | 2 | 2 | 35 | 35 | 35 |
| Low Temp. Flexibility | 0C | max | -5 | -5 | -5 | -5 | -5 | -5 | -5 | -10 | -10 | -10 | -10 | -10 | -10 | -10 | -20 | -20 | -20 | -20 | -20 |
| Flow Resistance | 0C | min | 120 | 120 | 120 | 120 | 120 | 120 | 120 | 120 | 120 | 120 | 120 | 120 | 120 | 120 | 100 | 100 | 100 | 100 | 100 |
| Impact Resitance | mm | min | - | - | - | - | - | 700 | 1000 | - | - | - | - | 700 | 1200 | 550 | - | - | - | - | 1000 |
| Tearing Resistance | N | ±%30 | 75 | 75 | 100 | 100 | 150 | 100 | 125 | 100 | 100 | 150 | 200 | 150 | 200 | 200 | 150 | 150 | 200 | 250 | 200 |
| Vapor Transmission | - | min | 20k | 20k | 20k | 20k | 20k | 20k | 20k | 20k | 20k | 20k | 20k | 20k | 20k | 20k | 20k | 20k | 20k | 20k | 20k |
| Reaction to Fire | Class | - | E |
